First of all, we need to know which way the mirror and seal strip are facing. If you have the same seal strip on both sides of your boat, make sure that you are able to notice that with a mirror. everbettermirror.com If the mirror is facing up, the seal strip is horizontal. You want to make sure that you can see the reverse side of your boat, which means that you want to have a mirror on the opposite side of the seal strip. Then you are able to align your mirror to the side you are looking at it.
If you have a different seal strip on each side of your boat, you will need to make a duplicate of the right side seal strip. You have to do this in such a way that you won’t be able to see your boat from the mirror. You have to make a mirror so that you will be able to see the opposite side. With your duplicate seal strip, you are going to go around the boat and make a mirror that is parallel to the two sides. Then you can rotate it to the other side and get a mirror that will be parallel with the mirror that you made for the other side.
Basically, you want the mirror to be at a slight angle to the side that you are facing and also so that it is facing the opposite side of the boat.
Now you need to think about where the mirror will be located. If you would like to get a mirror that is at an angle to the side, then you should mount it at the front of your boat. This way it will be on the same side of your boat, where the bright side will be pointing towards the sky.
If you would rather have it mounted higher on the side of your boat, then you will have to take your tape and make a huge square. You can either use a lampshade or an actual lampshade if you have one lying around. Then you can place the mirror under the shade and you can cut a circle out of the top. Finally, you will have to bend the circle so that it will not cover up your mirror.
Make sure that you are also flexible enough to fit the circle and the tape that you are going to use. Once you have made everything, you are going to need to mount the mirror on your boat, if you haven’t already.
Step By Step Guide to Mounting A Mirror:
Take the upper back part of a lamp shade. You will need to fold it down into a square so that it will fit under the lamp shade. Then you can use the taped piece as a template. If you haven’t made a mirror, then you can use a mirror from a toy box. Once the square has been cut out, you can place the tape on the shade and it will make a perfect fit for the mirror.
Now you are going to need to cut out a hole for the mirror. If you want to put the mirror in the front of your boat, then make sure that you turn the lamp shade upside down. You can also use a lighter if you don’t have one with you. Just make sure that you are able to clearly see that you are putting the mirror in the right place.
Once you have the hole cut, SEASHORE Rubber you are going to need to make a small piece of tape to put inside the hole. This is so that you will be able to hold the mirror so that it won’t fall.
Now it’s time to move the tape over. The back part of the lampshade will be completely folded over and it will not be visible. Now you are going to fold the front of the shade over so that the tape is hidden. Make sure that it is in a position where you are able to see the mirror from the front.
If you are using a mirror for the other side, then you can use the same procedure that you used on the other side.
Now you are going to need to make some small marks to show you where to put the mirror. Make a small dot right on the back of the tube and keep doing that until the part is visible. You can use the scissors to make some little marks.
Make sure that the exact height of the tube is shown so that you will be able to position the mirror correctly. Once you have a position, you will be able to get the mirror into position. Just hold it against the boat so that it is at a perfect angle.
If you still have some tape left, then you can also mark the size of the mirror. read more Once you have the mirror in the correct position, you can mount it using the tape.
Take the remainder of the tape and do the same as before.
Start to wrap the tape around the top of the boat. It should be long enough for the mirror to be in the right position. Wrap it around the bottom of the boat and keep doing that until you have a perfect fit.
Finally, you are going to need to make a small hole for the lampshade in the top of the tube. This will be so that you can change the light bulb inside the shade.
