7.9 C
New York
Friday, March 29, 2024

5 Simple Steps to Replace Your Car’s Ignition Switch

In almost every car on the road today, the ignition switch is generally the most important component. Even though the part is crucial to the operation of your car, ignition switch failure is a frequent problem these days. Although modern technology has helped users with an electronic key system, the ignition cylinder has its worth. Your car may stall, and other important functions like air conditioning will not work if the key doesn’t turn sideways due to a defective ignition switch. Because of this, ignition repair services are important. This article includes five fundamental steps to help you with ignition switch replacement.

1. Take the Battery Out and Turn to the Accessory Position

First, open the car’s trunk and remove the battery terminals. Know that the ignition cylinder cannot be removed until the cylinder has been turned to the accessory position, either manually or with a working key. It will be challenging if the key doesn’t turn in the switch or doesn’t even get inside. Make sure you clear anything that is obstructing the keyhole. If the key gets stuck inside the cylinder, you can use a hammer to gently tap on the key, turning it into the accessory position. However, lubricating the key and the keyhole will eventually make things easier.

2. Remove the Cover

Any ignition switch replacement will be left incomplete without the removal of the covering over it. Although, this procedure varies depending on the car. But make sure you do it properly and remember what you have done since you will have to reassemble it afterward. Don’t try to open anything forcefully to avoid the risk of breaking it. Instead, ensure that screws and other fasteners are saved for the appropriate panels. Before replacing your car key ignition, call a locksmith for ignition repair services if you experience any issues. Since the cover has many layers that must be removed, this portion of the car key ignition is probably the most time-consuming. As covers in more recent cars are fastened with security screws, some panels may even require specialized screwdrivers. 

3. Remove the Cylinder

After removing all the dashboard coverings from the area around the steering column, the ignition cylinder will be visible to you. Then look inside the housing to locate the retention pin. The pin becomes pressable when the cylinder is turned to the accessory position. To remove the cylinder, insert the pin and take the key out by rotating it. The retention pin is usually hidden under the switch assembly in most cars. To press the pin in, you will also require a tool. For that, most people make use of a thin pen. Ensure this tool is sturdy enough to prevent bending while pushing it inside the pinhole.

4. Install New Cylinder

With a few significant changes, this procedure in ignition switch replacement will be the same for installing the new ignition as it was for removing the old one. Just make sure that the new cylinder is of the appropriate size before placing it inside the assembly. However, place the new key inside the switch and rotate it to the accessory position to insert the cylinder into the housing. When you hear the retention pin moving into position, you will know that you have successfully inserted the cylinder into the housing. You can safely remove the key now that the cylinder is locked. However, run a few tests first, though, before removing the key. Continue with the next step while leaving the key in the ignition.

5. Final Testing After Reassembly

While the key is still in the accessory position, try pulling it out. The cylinder will break free if the retention pin isn’t fastened properly. However, if the cylinder is secured properly, try to start the car. Pull out the key and start the car again after turning it off. It is important to check whether your ignition switches are fully functional before reassembling the covers. However, if the cylinder has been replaced properly and your car still has issues, make sure to call a mechanic to check if there is another problem. When everything is operational, reattach the steering column and covers. Extreme precautions are required in this process as wiring can get loose. This can lead to serious problems, which will be costly. Hence, it is better to consult an expert before working on your ignition switch. If your car is stalling out or becoming more difficult to start in the mornings, there is a high chance of an ignition switch problem. More often, debris can get stuck in the ignition keyhole, making it difficult to turn the car key. However, depending on your skill level and knowledge, you can perform car ignition switch repairs or replacements yourself. While some repairs are simple, it’s best to leave the more difficult ignition repair services to the professionals. Call your nearest professional service today for incredible repairs.

Uneeb Khan
Uneeb Khan
Uneeb Khan CEO at blogili.com. Have 4 years of experience in the websites field. Uneeb Khan is the premier and most trustworthy informer for technology, telecom, business, auto news, games review in World.

Related Articles

Stay Connected

0FansLike
3,912FollowersFollow
0SubscribersSubscribe

Latest Articles